Washington DC Heating and Air Conditioning Contractor’s Guide: Basic HVAC Terminology

May 7th, 2012

Ever try to look up basic information about your Washington DC heating and air conditioning systems? There are dozens of terms that might as well be Greek for all you know – a mishmash of words and phrases talking about energy efficiency and air flow ratios. To make your next upgrade a little easier and give you a baseline with which to work, here are a few of the most common HVAC terms you’ll hear in the industry:

  • AFUE – Annual Fuel Utilization Efficiency – This is a simple measurement of how much fuel a furnace converts into actual heat in your home. So, if a furnace converts 92% of the fuel it consumes into heat, it has an AFUE rating of 92.
  • Watts – A single watt is a measurement of electricity. Commonly, your electricity use is assured in kilowatts or kilowatt hours (kWh).
  • BTU – British Thermal Unit – A BTU is a common measurement of how much energy is produced or consumed by an appliance. When referring to an air conditioner, one “ton” refers to 12,000 BTUs.
  • SEER/EER – Seasonal Energy Efficiency Ratio refers to how many BTUs can be produced with a single Watt of electricity per hour. So, an air conditioner with an SEER of 14 can produce 14 BTUs of cooling per watt consumed each hour.
  • HSPF – Heating Seasonal Performance Factor – Refers to the efficiency of the heating elements in your heat pump.
  • COP – Coefficient of Performance – A measurement of how effective your heat pump is at heating a space compared to standard electrical resistance heat. The lower the temperature gets outside, the lower the COP will be. Equipment is usually measured for COP at 47 and 17 degrees to give an idea of seasonal performance of a new heat pump.
  • Refrigerant – Refrigerant is any gas that is used to draw heat from the air in a particular environment through an air conditioner or heat pump. It has a much lower boiling point than water, allowing it to cool despite the temperature outside. Currently, most equipment uses R-22 refrigerant while the new standard will be R-410A (Puron), legally required in all cooling units by 2020.
  • CFM – Cubic Feet per Minute – Used to measure the volume of air passed through an air handler by an air conditioner or furnace.

There are a number of complicated details to keep track of when choosing a new air conditioner or furnace. To ensure you get the very best out of your Washington DC heating and cooling system, read up on these details in advance – you’ll feel a heck of a lot smarter when you call. For any HVAC service you need in the Washington DC area, give Polar Bear Air Conditioning a call!

Continue Reading

Common Air Conditioner Problems in Washington DC

April 23rd, 2012

Air conditioners are an important part of our lives. They keep us comfortable despite overbearing heat and humidity outside all summer, but because they run constantly for months and because they are such complicated pieces of machinery, they can experience some problems. Here are some of the most common problems you’re likely to run into with your Washington DC air conditioner and how to solve them:

 Leaks

A common problem that many people ignore or are unaware of is refrigerant leakage. It is possible that when the system was installed, it wasn’t properly charged, but most of the time if your system is low on refrigerant, it is because of a leak. You can’t just pour more refrigerant in and call it good, though.

The leak needs to be fixed, both for health and environmental reasons. If you notice that your system is low on refrigerant or you smell something off – often like acetone, call a professional immediately for inspection and repair.

 Sensors

An air conditioner doesn’t do you any good if the sensors don’t work properly. Improperly working sensors will fail to properly read the temperature in the home or from your thermostat. So, it might be 80+ degrees in your home but if the thermostat reads it as 72, the system won’t turn on. The air conditioner itself probably still works fine, but unless it can successfully read the temperature, you won’t get the cooling you need to stay comfortable.

Check first to see if the sensor was moved or knocked toward the evaporator coil (which will keep the temperature reading low).

 Drainage Problems

Your air conditioner acts as a dehumidifier as well, producing a liquid known as condensate. This liquid usually drains from the air conditioner into a designated area away from your home. However, if the condensate drain gets clogged or if the system wasn’t properly installed, that condensate can start to build up in your home. If you notice leakage around the coils, you may need a pump to remove the condensate properly.

Properly maintaining your air conditioner can usually be done with regular maintenance each year, but if one of these problems pops up, call a Washington DC air conditioning professional and get them fixed right away.

For any AC maintenance or repair, give Polar Bear a call today!

Continue Reading

Washington DC Air Conditioning Guide: How to Calculate Duct Size for an AC System

April 9th, 2012

Duct sizing is a complex process using one of three methodologies. The goal of duct sizing is to provide the perfect space through which heated and cooled air can travel around your home. Ducts should provide ample air flow to keep you comfortable without overworking your Washington HVAC system or costing you an arm and a leg on your energy bill.

Methods Used for Sizing

There are three methods used for most modern duct sizing. The first is the Velocity Method. The velocity method takes into account the speed at which air flows through the ducts based on their general size. A series of equations is used to determine this, including duct cross sectional area, air flow rate and air speed. A much more detailed breakdown is available on the EngineeringToolbox.com for those interested in the math behind the process.

In general though, the velocity method allows contractors to determine the appropriate size and layout of ducts based on their application (residential, commercial, industrial or high speed) and their position (main or branch ducts).

Contractors may also use the Constant Pressure Loss and Static Pressure Recovery methods to design ductwork for your HVAC system. The constant pressure loss method tends to result in more components but provides a more accurate reading of the actual pressure loss in the system based on the materials used and the layout of your ductwork.

Static pressure recovery focuses on ensuring the same pressure level is achieved at all vents and inlets for the system. It is probably the most complicated sizing method, however, so it is rarely used for residential installations.

Simplifying the Process

Were we to break down the process into its core components, this is what a Washington DC air conditioning contractor would do when sizing your duct work:

  • Determine CFM for Each Room – using the Manual J for load calculations, they would determine the CFM. This is based on the (Room Load/House Load) x Equipment CFM. The entire house must be measured and load calculations completed before this can be done.
  • Friction Loss Rate – Friction loss rate is the (Available Static Pressure x100 / Effective Length).
  • Duct Sizing – Finally, the contractor will use a chart or software to select ductwork based on the friction loss and CFM calculated in the first two steps.

The goal of all of this math is to ensure that the system installed is exactly as large as is necessary to distribute heated or cooled air to the entire house. Incorrect measurements result in improper delivery of that air and a system that doesn’t quite get the job done.

Continue Reading

Reasons Your Washington DC Heat Pump Can’t Maintain the Right Temperature

March 26th, 2012

When you set your thermostat for a certain temperature, you expect that your Washington DC heat pump will either heat or cool it to that temperature, right? When you want 72 degrees, you don’t expect to have the temperature stay stuck at 70 degrees while your heat pump struggles futilely.

Sometimes heat pumps have trouble maintaining the right temperature, especially in heating mode. It’s not uncommon, and it has a number of potential causes. Run through this checklist to see if it is something you can fix yourself:

  • The outdoor unit is iced up. Running a defrost cycle can usually fix this.
  • The outdoor unit is not running at all. Sometimes this is simple enough to fix on your own. Read the manufacturer’s instructions to troubleshoot the problem.
  • Too much cold air is getting in the house for the heat pump to keep up. Make sure your doors and windows are closed to keep that valuable heat inside.
  • Your vents are closed. It may seem obvious, but problems like this can sometimes be attributed to user error. Make sure your vents are open to allow heat in.

This is by no means an all-inclusive list, and it covers just those causes that you could potentially fix yourself. There are many other possible culprits out there that could be more sinister and require Washington DC heating and air conditioning professional to be properly repaired.

Some of these include:

  • The compressor is not running.
  • A compressor valve or reversing valve is faulty.
  • The thermostat is malfunctioning or needs to be recalibrated.
  • The refrigerant level is low or there is a problem with the flow of the refrigerant.
  • The heat pump needs routine maintenance.

If your heat pump is not working properly for several days, especially after you have tried some of the DIY solutions above, call Polar Bear Air Conditioning right away. Your heat pump may need repairs before a bigger problem develops.

Continue Reading

Washington DC Heating Tip: Dangers of Not Changing Your Furnace Filter on Time

March 14th, 2012

Of the many ways to heat a home in Washington D.C., forced air systems are the simplest in function and the easiest to maintain.  They are so simple, in fact, it is easy to forget they need attention at all, but there are dangers to not changing your furnace filter on time that have a real and painful cost in efficiency and dollars.  Even health risks arise when filters have been neglected too long.

Contracting with a company like Polar Bear Air Conditioning ensures consistent maintenance and oversight to allow Washington D.C.  homeowners the comfort and relaxation you deserve in your own home.

Back to Basics

Usually in the basement or a central location, a furnace heats air to a temperature set by the thermostat.  Over the years, technological improvements have enabled furnaces to be much smaller and fit into closets instead of the large and gangly monsters of old that could fill an entire basement.

By a fan in the furnace, the warm air is circulated through filters into a system of ducts to be distributed to grates in the wall or registers on the floor.  A second grate and duct system returns cooler air back to the furnace to be reheated.

Water can be added at the furnace to humidify the air and filters are able to remove some of the dust that typically floats invisibly throughout a home.

The Dangers of Not Changing the Filter

When the system is properly maintained, it is clean, efficient and produces comforting heat on demand at the touch of the thermostat or consistently throughout the day and night.

The furnace filter is designed to remove dust from air as it passes through your furnace. The longer your furnace filter is in place the dirtier it becomes. The increase of particles caught in the filter creates resistance to air flow through the filter and reduces efficiency.

To make up for the loss of flow through a dirty filter, the heat exchanger, usually a gas or oil fired flame, must work harder to produce the same amount of heat to the space.  This becomes costly financially and causes undo wear and stress on the equipment, requiring a partial or full replacement much sooner.

Additionally, operating above ideal designed conditions, cracks in the chamber may appear from the over load which can allow carbon monoxide, a toxic gas, to be released into the duct work.  This gas in large quantities in the home can cause headaches, nausea, and in extreme circumstances, even death.

Regular Maintenance

To avoid problems and excessive strain, remember to change the filters at the beginning of each new heating season.  An annual maintenance, check-up and thorough cleaning by a qualified company like Polar Bear Air Conditioning ensures a safe and comfortable season of warmth with no need to worry about the dangers of not changing filters in your furnace.

Continue Reading

Washington DC HVAC Contractor Tip: Things You Can Do to Make Your Heating System More Effective

February 29th, 2012

Have you ever wondered why it is too hot or too cold in your Washington DC home? You can always blame it on the thermostat or an open or closed window. Those are easy targets. But maybe the real culprit is your heating and cooling system, namely your furnace or air conditioner. Maybe these pieces of equipment have to work extra hard because of something as simple as a dirty filter that you should have cleaned or replaced.

Learning how to make your heating and cooling system more “effective” does not require a physics degree or an extensive knowledge of the refrigeration cycle. In most cases, it just takes common sense – and a little creativity.

For example, did you know that how your home is insulated can have a direct impact on how well your heating and cooling equipment functions? It sure can. If your walls, crawl spaces, or attic is poorly insulated or not insulated at all, your furnace and air conditioner will have to work harder to keep up – and keep you warm or cool. In some cases, your heating and cooling equipment might never be able to give you the desired temperature on your thermostat setting because the equipment has to work too hard to make up for lost heat or cooling due to poor insulation.

So what should you do? Find out if your home is properly insulated by having a load calculation or energy audit on your home. Any licensed and qualified heating and cooling contractor will be able to perform one of these tasks for you and show you where you might be losing too much of your indoor air to poor insulation. This same test can also detect any leakage through cracks in the foundation or joints or connections in ductwork. Windows and skylights are also an area of heat loss or gain. Installing awnings or trees can cut down on this loss or gain, too.

Of course, the most effective heating and cooling system is one that is serviced and properly maintained on a regular basis. If you have any questions on system maintenance, call Polar Bear and schedule a tune-up today.

Continue Reading

Washington DC Heating Question: Can Your Heating System Warn You of a CO Leak?

February 22nd, 2012

As everyone in Washington knows, carbon monoxide is a serious health risk. It is an odorless gas that is produced as a natural byproduct of combustion. So, any time something burns, carbon monoxide (CO) is released into the air.

As long as the area is properly ventilated, the carbon monoxide cannot build up in the air to a dangerous level of concentration. For example, if you are around a campfire or charcoal that is burning outside, you are generally safe.

In the home, the danger arises when combustion is not properly ventilated and this toxic gas is allowed to seep into our living spaces. If you use any gas, fuel or wood burning appliances in your home, you are at risk for exposure to carbon monoxide. To help mitigate that risk, it is important to know some warning signs. Your heating system gives off some warnings that can tip you off to danger, so be on the lookout for these three signals:

  1. Carbon monoxide detector goes off. Some heating systems these days have built-in carbon monoxide detectors, which can provide an extra measure of safety. Whether you have one of these systems or not, your home should still be equipped with a CO detector. If it begins sounding the alarm, get everyone out of the house immediately.
  1. A fume vent is leaking. Fuel-burning furnaces have vents to move combustion gases out of the house safely. If you notice this vent is leaking on your heating system, CO may be seeping into your house. Shut down the furnace, open windows for ventilation and have the fume vent repaired immediately.
  1. Smoke backing up from the fireplace. If you have a fireplace and you notice smoke in the room while using it, stop using it immediately. Your chimney may be blocked or leaking, preventing the smoke from rising and venting properly, which means CO can e getting into your house. Do not use the fireplace again until you have had the chimney inspected.

Please take care and note this is just a simple guide. There are other risks and warnings of carbon monoxide. If you have any suspicion that there is CO in your home, immediately call Polar Bear Air Conditioning to look into the situation.

Continue Reading

Happy President’s Day from Your Washington DC Area HVAC Contractor!

February 20th, 2012

Everyone at Polar Bear Air Conditioning and Heating wishes you a very happy President’s Day! We hope you all get a chance to take advantage of some of the great sales! It is also a great time to think about how you can make your community a better place. Lend a neighbor a helping hand or volunteer your time; everyone doing a little good can make a big difference!  Being more green is also a good way to help you community, and upgrading your HVAC system can be a big part of that. If you have an older system that is using a lot of fuel, a new system will not only save you money but also help you make your home more environmentally friendly, which is good for everyone.

One of the traditions of celebrating Presidents Day is food made with cherries, in honor of George Washington, so here is a great recipe for some Cherry-Blueberry Pie:

“A fruity and fun surprise awaits you inside this double crusted cherry and blueberry pie.”

INGREDIENTS:

1 (15 ounce) package refrigerated pie

crusts

1/2 cup white sugar

2 tablespoons cornstarch

1/4 teaspoon ground cinnamon

1 (21 ounce) can cherry pie filling

1 1/2 cups frozen blueberries

1 egg white

1 teaspoon water

2 teaspoons sugar

DIRECTIONS:

  1. Preheat the oven to 425 degrees F (220 degrees C).
  2. Press one of the pie crusts into a 9 inch pie plate. In a large bowl, stir together 1/2 cup of sugar, cornstarch and cinnamon. Stir in the cherry pie filling and blueberries. Spoon into the pie crust. Top with the second crust, and press the edges to seal. Flute edges, or press with the tines of a fork. In a cup, whisk together the egg white and water with a fork. Brush over the top of the pie, then sprinkle with 2 teaspoons of sugar.
  3. Bake for 45 to 55 minutes in the preheated oven, or until crust is golden brown. Cover the edges of the crust with aluminum foil if they appear to be getting too dark. Cool for at least 2 hours to allow the filling to set before serving.

This recipe is from allrecipes.com, visit their site for more details!

Continue Reading

Happy Valentine’s Day from Your Washington D.C. Area Heating and Air Conditioning Contractor!

February 14th, 2012

We wish you a very happy Valentine’s Day! Valentine’s Day is the perfect time to show your appreciation to everyone who makes a difference in your life. Even a small gift, like a batch of cookies or a homemade card, can really make someone feel special. Your friends, your family, and your significant other will all have a fantastic Valentine’s Day if you take a moment to let them know how important they are to you.

Calling us for an HVAC upgrade might seem like a usual gift, but it can actually be something that benefits your whole family. An improved indoor air quality system can make your air cleaner and healthier, and a new heating system can make your home more comfortable and save you money by lowering your utility bills. Those are improvements that every member of your family can enjoy.

If you have any questions about upgrades for your heating and air conditioning system, give Polar Bear Air Conditioning a call today! And to help you celebrate this sweet holiday, here is a recipe for Chocolate Cakes with Liquid Centers:

“Warm, soft and gooey chocolate cakes. Perfect for that ubiquitous chocolate fix. A good-quality bittersweet chocolate is necessary for the success of these cakes.”

INGREDIENTS:

1/2 cup butter

4 (1 ounce) squares bittersweet

chocolate

2 eggs

2 egg yolks

1/4 cup white sugar

2 teaspoons all-purpose flour

DIRECTIONS:

  1. Preheat oven to 450 degrees F (230 degrees C). Butter and flour four 4 ounce ramekins or custard cups.
  2. In the top half of a double boiler set over simmering water, heat the butter and the chocolate until chocolate is almost completely melted.
  3. Beat the eggs, egg yolks and sugar together until light colored and thick.
  4. Beat together the melted chocolate and butter. While beating, slowly pour the chocolate mixture into the egg mixture, then quickly beat in the flour and mix until just combined.
  5. Divide the batter between the four molds and bake at 450 degrees F (230 degrees C) for 6 to 7 minutes. The centers of the cakes will still be quite soft. Invert cakes on serving plates and let sit for about 15 seconds, then unmold. Serve immediately with fresh whipped cream, if desired.

For more details, visit allrecipes.com.

Continue Reading

Washington DC Heating Repair: $25.00 off Any Service Call!

February 8th, 2012

Heating repairs can be extremely inconvenient for any homeowner. Not only is your heat broken, but many heating repairs can be expensive. That is why you need to have the number of a contractor that you can trust, someone who will get the problem fixed fast and at a fair price.

Polar Bear Air Conditioning and Heating is dedicated to customer service and fair pricing. All of technicians will respect your home, your  family, and your equipment; we know that each situation is different and we do our very best to make sure that every customer is satisfied. To make it even easier to call Polar Bear with any repairs you might need this year, we are offering $25.00 off any service call! Remember that having any problems you notice fixed now might save you from a major repairs or replacement later.

Call for details!

Continue Reading