Polar Bear Air Conditioning & Heating Inc. Blog: Posts Tagged ‘Washington DC’

Washington DC Heat Pump Guide: Common Heat Pump Performance Problems

Monday, September 10th, 2012

The heat pump in your Washington DC home needs to work year round to provide heat and air conditioning. This is why you want to make sure it’s performing as efficiently as possible to save on energy costs and prevent break downs. You should schedule an annual maintenance check-up and inspection with a certified HVAC technician to test the efficiency levels.

However, there are a few common causes of performance issues to be aware of so that you can be sure your Washington DC heat pump performs at optimal levels. Call Polar Bear if you have questions about heat pump performance issues, or to make an appointment for an annual inspection and professional cleaning.

Airflow Issues

There should always be a certain amount of airflow (measured in cubic feet per minute) in your heat pump to maintain proper efficiency levels. If the airflow is less than 350 cfm per ton, it could increase your energy costs. You should make sure your HVAC contractor checks the airflow whenever your heat pump is inspected. Always keep the coils clean. Sometimes the ducts are not the right size, or the fan speed needs to be increased, but often cleaning the coils will help airflow, which is why it is important to clean and maintain the components of your heat pump. A certified technician will know what methods are best, so if you suspect an airflow problem with your heat pump, call a professional heating technician.

Air Leaks in the Duct System

Inefficient or poorly-designed duct systems may not distribute air properly throughout your home because of potential air leaks. There should always be a balance between the intake and return air in a forced air system, which helps maintain a neutral pressure within the house and increase efficiency. Some contractors argue over how tightly a house should be sealed for this reason, but if your heat pump is losing heat through leaks in the air ducts, this will greatly affect its efficiency.

Improper Refrigerant

Refrigerant leaks are another common cause of low performance levels in heat pumps. Most heat pumps already have refrigerant when they leave the factory and shouldn’t have any issues. Heat pumps that are charged with refrigerant when they are installed can sometimes have the wrong amount of refrigerant. Either too much or too little refrigerant will lower the heat pump’s efficiency and performance levels. Always check the recommended refrigerant amount or ask an HVAC technician before you add refrigerant yourself.

If the heat pump in your Washington DC home isn’t working properly, it is also affecting your heating bills. Call Polar Bear today to set up an appointment.

Continue Reading

Tags: , ,
Posted in Heat Pumps | Comments Off on Washington DC Heat Pump Guide: Common Heat Pump Performance Problems

Washington DC Air Conditioning Repair Guide: Air Conditioning Condensate Problems

Tuesday, September 4th, 2012

The beauty of air conditioning in Washington DC is that we don’t have to do anything to live in a cool climate even when it’s boiling outside.  Programmed to adjust automatically, modern thermostats make it even easier.

Air Conditioning 101

The process of conditioning air to a cooler temperature involves rapid evaporation and condensation of chemicals called refrigerants.  These are compounds having properties that allow them to change from liquid to gas and back at low temperatures.

When the liquid evaporates and transforms into gas it absorbs heat.  Compressed tightly together again, the matter condenses back into liquid with a residue of unwanted moist heat that must be released to the outdoors.

Over the course of handling the air to cool it, air conditioners are able to filter dust and dehumidify the air as well.  This release of moisture is why air conditioners have drains.

Condenser Coils

As the heat is removed from the gas, it forms condensation that must be drained from the system.  Tiny particles accumulate along the path, prone to shifting and resettling until they become lodged and can form a significant enough blockage to hamper the efficiency of the unit.  If the drain line becomes blocked, the unit drips or overflows the pan and works its way back into the house, causing damage and potentially mold.

Easy Fix

A simple act of maintenance performed twice a year and requiring no tools can eliminate the problem.  To check and maintain your condensate drain, these are the steps your AC technician will perform:

On the interior side, they will remove the panel of the unit and find the drain line, usually a plastic tube.  If the pan is full of water, there is a blockage.  On a whole house system, they then find where the plastic tube exits the house, making sure that it is above ground and clear to drain away. Flush the line with a short burst from a hose.

Regular maintenance is simply a 1/2 cup of warm water poured down the tube to ensure a clean and free flowing pipe, which can be taken care of during your annual maintenance visit. Call Polar Bear Air Conditioning and Heating today if you need heating or air conditioning service in Washington DC and the surrounding area!

Continue Reading

Tags: , , ,
Posted in Air Conditioning | Comments Off on Washington DC Air Conditioning Repair Guide: Air Conditioning Condensate Problems

Heat Pump Maintenance Tips from Washington DC: What Happens When You Neglect to Maintain Your Heat Pump System

Monday, August 27th, 2012

Just like any HVAC system, the heat pump in your Washington DC home needs routine maintenance and yearly check-ups to operate as efficiently and safely as possible. You also don’t want your heat pump to wear down to the point of a major malfunction or breakdown, which can be costly to repair or may require a complete system replacement.

Here are some things that could go wrong and cost you a lot more in the end if you don’t keep up with the regular maintenance of your Washington DC heat pump.

Damage to the Compressor

The compressor in a split-system heat pump works whether you are heating or cooling your home. In the winter, the compressor reverses the flow of the refrigerant to defrost the outdoor coils, and in the summer it supplies the refrigerant to cool the home, as well as cooling the outdoor coils. Proper airflow is vital to keeping the compressor running smoothly. Filters that are not changed regularly, dirty coils, and dirty fans can all restrict airflow, which will damage the compressor. Debris around the outside components should also be cleared to allow proper airflow.

Decreased Efficiency

When dirty or broken components restrict the airflow, this damages the compressor and decreases the heat pump’s efficiency levels.  Not only is it important to clean your heat pump regularly, but you should also have it checked by a certified heating technician once a year. This will also prevent safety hazards and other hidden issues with the heat pump.

Improper Refrigerant Levels

Most heat pumps are charged with refrigerant at the factory; however, if models that are charged when they are installed are not given the right amount of refrigerant this can also affect performance levels. Refrigerant leaks and other common problems can be prevented by scheduling an annual maintenance visit with one of our qualified technicians.

Don’t wait until the heat pump in your home stops working, call Polar Bear Air Conditioning to schedule your yearly check-up today!

Continue Reading

Tags: , , ,
Posted in Heat Pumps | Comments Off on Heat Pump Maintenance Tips from Washington DC: What Happens When You Neglect to Maintain Your Heat Pump System

Washington DC Air Conditioning Tip: Programmable Thermostats and Your AC

Monday, August 20th, 2012

Air conditioning makes our Washington DC homes comfortable during a hot summer day. However, air conditioners need electricity to run, and most of us are trying to reduce our home’s energy consumption. There are a number of ways you can make your air conditioning system more efficient, including upgrading to an ENERGY STAR rated unit and scheduling regular maintenance, but one of the easiest steps to implement is installing a programmable thermostat.

Programmable thermostats automatically adjust the temperature in your home depending on the time of day. You can save up to 10 percent a year by turning down your thermostat back ten degrees for eight hours a day! Most models allow you to store multiple daily settings, so you can turn you air conditioner down during the day when you are at work and while you are sleeping, and still have the temperature cooler when you need it. You can also still manually adjust the temperature without affecting the normal settings, giving you complete control and helping you save energy.

Programmable thermostats are not all made the same, and there are many different makes and models. An HVAC contractor will go over the different features available to you so you can decide which best fits your needs. Different thermostats work better with different systems, for instance some heat pumps need thermostats that have multi-stage functions, so it is best to consult with a Washington DC air conditioning and heating professional before deciding what to purchase.

Programmable thermostats allow you to save energy without sacrificing comfort, which is something that all of us are looking for. If you are looking for a simple, affordable way to improve your HVAC system, a programmable thermostat is a great choice. Most are easy to read and easy to use, call Polar Bear Air Conditioning today to learn more about having a programmable thermostat installed in your home!

Continue Reading

Tags: , , ,
Posted in Air Conditioning | Comments Off on Washington DC Air Conditioning Tip: Programmable Thermostats and Your AC

Washington DC Air Conditioning Tip: Things You Should Never Do To Your Air Conditioner

Monday, August 13th, 2012

Whether it’s a large central system or a small on, with proper care and maintenance, your Washington DC air conditioner should last for a quite a while.  Sometimes, however, people can do simple things which, in retrospect, should have obviously been avoided.

Some examples:

  • Don’t block the air intake–air is vital to the process, so laying anything over the unit (a towel or clothes to dry) will significantly strain the motor.  Always make sure there is enough clearance.
  • Don’t block the vents–likewise in a home, it is easy to move a sofa or lay an area rug over a grate in the floor or cover an unsightly vent in the wall with a pretty painting.
  • Don’t think it will run forever without cleaning the fins, vents and changing the filter at least once a heating season;
  • Don’t leave the units exposed in winter–always cover when not in use for long periods of time;
  • Don’t bury the condensate drain in the ground–in central units it is vital that the drain is left with a clear flow away from the house;
  • Don’t steam clean or use hot water to clean the fins–damage and corrosion can easily be caused by the heat; flush with warm water or spray.
  • Don’t remove the overload relay to force continuous running–VERY dangerous and a guarantee of damage.

A little attention to your Washington DC air conditioning  goes a long way to ensure years of comfort. Call Polar Bear Air Conditioning if you need to schedule a maintenance visit!

Continue Reading

Tags: , , ,
Posted in Air Conditioning | Comments Off on Washington DC Air Conditioning Tip: Things You Should Never Do To Your Air Conditioner

Washington DC Air Conditioning Tip: Icing Problems on Air Conditioner Cooling Coils

Monday, July 2nd, 2012

Air conditioning cooling coil icing problems can arise for a couple of reasons: either the air filter has not been properly replaced, or there is a condensing coil leak.  It is best to check and test the easiest problem first and then move on from there.

It is important to replace air conditioning filters as often as is recommended by the manufacturer.  A common result of not replacing filters frequently enough is a buildup of dust and dirt on the filter, which causes reduced air flow throughout the air conditioning unit.  With reduced air flow, the evaporator coil or cooling coil within the air handler can become blocked by ice or frost build-up.  Having cooling coil icing can significantly reduce or completely stop the amount of cool air being produced by an air conditioning unit.

Easy steps to diagnose and resolve air conditioning cooling coil icing problems:

  • Visually inspect the air conditioning cooling coils to check whether reduced air flow has been caused by cooling coil icing.  If ice or frost is found on the coils, thus blocking air-flow, proceed with the next step.
  • Turn off the air conditioning system completely to allow ice to evaporate, the unit will have to remain off until all ice is completely melted and drained away from the unit
  • Replace all dirty filters on the air conditioning unit
  • Once the a/c unit is de-iced and has fresh filters, it is safe to turn the system back on, to test whether the icy build-up happens again

If after completing these steps, when the air conditioning unit is turned back on cooling coil icing happens again, this could mean one of two things.  Either too little of the refrigerant is being released into the cooling coil due to a clogged capillary tube or a stuck thermostatic expansion valve.  Or the refrigerant charge is too low due to a refrigerant leak.  A refrigerant leak can happen at any point in the refrigerant piping system which would then need to be soldered and resealed, or it can happen in the cooling coil or condensing coil which could mean the entire coil needs to be replaced.  Fixing of refrigerant leaks should be handled by a Washington DC air conditioning  professional.  Contact Polar Bear Air Conditioning, one of our HVAC technician can identify the air conditioner cooling coil icing problem and execute the proper solution.

Continue Reading

Tags: , ,
Posted in Air Conditioning | Comments Off on Washington DC Air Conditioning Tip: Icing Problems on Air Conditioner Cooling Coils

Washington DC Air Conditioning Tip: Why Replace Your Indoor and Outdoor AC Components at the Same Time

Monday, June 18th, 2012

Do you need to replace one of the main components of your Washington DC split AC system? If so, you are probably tempted to just replace whichever unit is failing in order to fix the problem quickly and cheaply. This is not always the best way to go, however. Here are six reasons why you should replace both the indoor and outdoor units at the same time.

#1: Cost

Although replacing just the failing component – whether indoor or outdoor – will be less expensive up front, that choice often proves more costly overall. You will see just what that means in the rest of these reasons.

#2: Advances in design

Heating and cooling technology is always advancing, so since you purchased your Washington DC air conditioning system, the products on the market have gotten quieter, more efficient and better overall. By replacing just the failing indoor component, you won’t reap all the benefits of this new technology, as the older outdoor component will still lag behind the times.

#3: Higher efficiency

When both units are replaced at the same time, and with models that have the same technology, they work together more efficiently. That means more savings on your bills and a more comfortable home.

#4: Matched system

Split AC systems are designed such that the indoor units are engineered to work best with a matching outdoor unit. When the system is matched, you get optimum performance and efficiency. By replacing just one component, you lose the benefits of that matching, meaning degraded efficiency and performance.

#5: Warranty considerations

A new system means new warranty coverage. Replacing both units at once means a whole new warranty that covers your whole cooling system, so you won’t have to worry about paying for any more replacements jobs for a long time.

#6: Wear and tear

Finally, think about the wear and tear your Washington DC air conditioning system has undergone since it was installed. Maybe only your outdoor unit needs to be replaced now, but since your indoor unit has tolerated the same number of hours of use, it may be on its way out sooner than later. It’s like when you buy new tires for your car– you don’t buy one or two, you buy a whole set of four so that the whole system starts fresh. That way you only do it once, and not again in six months or a year.

For all these reasons, replacing both components of a split system is often the best and least expensive route to choose when facing a replacement. For more information about Washington DC air conditioning installation, give Polar Bear Air Conditioning a call today!

Continue Reading

Tags: , ,
Posted in Air Conditioning | Comments Off on Washington DC Air Conditioning Tip: Why Replace Your Indoor and Outdoor AC Components at the Same Time

Washington DC Air Conditioning Tip: Air Filter Sizing

Monday, June 4th, 2012

If you moved into a new home or had someone change the filters on your Washington DC air conditioning or heating system for you, you may notice that whoever did the job put on the wrong size filter. This is not uncommon and is usually the result of an effort to save either time or money. However, in the long run it actually costs both. Here is how you can fix the problem of a wrong size filter.

The WRONG Way

If you have a filter that is too big for your system, it may seem like an easy enough fix– just fold it over or trim it down, right? Not so fast.

Folding the filter over makes for an imperfect seal. Air will leak through and around the bend, bypassing the filter entirely. This causes dirt and debris to build up on the fan, slows down air flow, degrades performance, decreases air quality and overall makes a big mess that you will have to pay to fix or clean up later.

Bending or cutting the filter also decreases its structural integrity. The whole filter can collapse while installed, creating not just a performance issue and a potentially costly repair, but also possibly creating unsafe conditions.

Furthermore, don’t give into the temptation to run your Washington DC air conditioning or heating system without a filter for the time being. The debris will quickly build up in your AC system, as well as being blown into your home. Heating and cooling systems should always be operated with the proper filter installed.

The RIGHT Way

So, what do you do when you have an air filter that is the wrong size? The only solution is to find the right size. If you are having trouble finding the right air filter for your system, try these tips:

  • Refer to your owner’s manual for the filter model number.
  • Bring the make and model information of your heating/cooling system to the store and ask someone there for help.
  • Have a professional inspect your system and replace the filter. (You should have a professional inspection once a year, anyway.)
  • For HVAC systems that are large or have special dimensions, special order custom filters to fit.

Above all, never operate your HVAC system without a clean, correctly sized filter properly installed. For more information about about which air filters are best for your system, give Polar Bear Air Conditioning a call!

Continue Reading

Tags: , , ,
Posted in Air Conditioning | Comments Off on Washington DC Air Conditioning Tip: Air Filter Sizing

Washington DC Heating and Air Conditioning Contractor’s Guide: Basic HVAC Terminology

Monday, May 7th, 2012

Ever try to look up basic information about your Washington DC heating and air conditioning systems? There are dozens of terms that might as well be Greek for all you know – a mishmash of words and phrases talking about energy efficiency and air flow ratios. To make your next upgrade a little easier and give you a baseline with which to work, here are a few of the most common HVAC terms you’ll hear in the industry:

  • AFUE – Annual Fuel Utilization Efficiency – This is a simple measurement of how much fuel a furnace converts into actual heat in your home. So, if a furnace converts 92% of the fuel it consumes into heat, it has an AFUE rating of 92.
  • Watts – A single watt is a measurement of electricity. Commonly, your electricity use is assured in kilowatts or kilowatt hours (kWh).
  • BTU – British Thermal Unit – A BTU is a common measurement of how much energy is produced or consumed by an appliance. When referring to an air conditioner, one “ton” refers to 12,000 BTUs.
  • SEER/EER – Seasonal Energy Efficiency Ratio refers to how many BTUs can be produced with a single Watt of electricity per hour. So, an air conditioner with an SEER of 14 can produce 14 BTUs of cooling per watt consumed each hour.
  • HSPF – Heating Seasonal Performance Factor – Refers to the efficiency of the heating elements in your heat pump.
  • COP – Coefficient of Performance – A measurement of how effective your heat pump is at heating a space compared to standard electrical resistance heat. The lower the temperature gets outside, the lower the COP will be. Equipment is usually measured for COP at 47 and 17 degrees to give an idea of seasonal performance of a new heat pump.
  • Refrigerant – Refrigerant is any gas that is used to draw heat from the air in a particular environment through an air conditioner or heat pump. It has a much lower boiling point than water, allowing it to cool despite the temperature outside. Currently, most equipment uses R-22 refrigerant while the new standard will be R-410A (Puron), legally required in all cooling units by 2020.
  • CFM – Cubic Feet per Minute – Used to measure the volume of air passed through an air handler by an air conditioner or furnace.

There are a number of complicated details to keep track of when choosing a new air conditioner or furnace. To ensure you get the very best out of your Washington DC heating and cooling system, read up on these details in advance – you’ll feel a heck of a lot smarter when you call. For any HVAC service you need in the Washington DC area, give Polar Bear Air Conditioning a call!

Continue Reading

Tags: , , ,
Posted in Air Conditioning, Heating | Comments Off on Washington DC Heating and Air Conditioning Contractor’s Guide: Basic HVAC Terminology

Reasons Your Washington DC Heat Pump Can’t Maintain the Right Temperature

Monday, March 26th, 2012

When you set your thermostat for a certain temperature, you expect that your Washington DC heat pump will either heat or cool it to that temperature, right? When you want 72 degrees, you don’t expect to have the temperature stay stuck at 70 degrees while your heat pump struggles futilely.

Sometimes heat pumps have trouble maintaining the right temperature, especially in heating mode. It’s not uncommon, and it has a number of potential causes. Run through this checklist to see if it is something you can fix yourself:

  • The outdoor unit is iced up. Running a defrost cycle can usually fix this.
  • The outdoor unit is not running at all. Sometimes this is simple enough to fix on your own. Read the manufacturer’s instructions to troubleshoot the problem.
  • Too much cold air is getting in the house for the heat pump to keep up. Make sure your doors and windows are closed to keep that valuable heat inside.
  • Your vents are closed. It may seem obvious, but problems like this can sometimes be attributed to user error. Make sure your vents are open to allow heat in.

This is by no means an all-inclusive list, and it covers just those causes that you could potentially fix yourself. There are many other possible culprits out there that could be more sinister and require Washington DC heating and air conditioning professional to be properly repaired.

Some of these include:

  • The compressor is not running.
  • A compressor valve or reversing valve is faulty.
  • The thermostat is malfunctioning or needs to be recalibrated.
  • The refrigerant level is low or there is a problem with the flow of the refrigerant.
  • The heat pump needs routine maintenance.

If your heat pump is not working properly for several days, especially after you have tried some of the DIY solutions above, call Polar Bear Air Conditioning right away. Your heat pump may need repairs before a bigger problem develops.

Continue Reading

Tags: , ,
Posted in Heat Pumps | Comments Off on Reasons Your Washington DC Heat Pump Can’t Maintain the Right Temperature